1. kamerák
  2. Car Audio & Electronics
  3. Home Audio
  4. Personal Audio
  5. TV-k
  6. Okos otthon
  >> Elektronikai Technológia Online >  >> Car Audio & Electronics >> Car audio és videó tartozékok

Dupla Din fejegység telepítése és áttekintése 2002–2005 Mercedes CLK 320

Ebben a cikkben: Végigvezetjük a dupla dínós fejegység beszerelésének lépésein egy 2002–2005-ös Mercedes CLK 320-ba, és áttekintjük az általunk használt fejegységet.

  • Beszerelés 2002-2005 Mercedes Benz CLK320
    • A telepítéshez szükséges alkatrészek
    • 1. lépés:Válassza le az akkumulátort
    • 2. lépés:Távolítsa el a Dash Trim-et
    • 3. lépés:Csavarja le és távolítsa el az OEM-fejegységet
    • 4. lépés:Készítse elő a kábelköteget és a fejegységet
    • 5. lépés:Bekötési tartozékok:antennák, USB és mikrofon
    • 6. lépés:Az új fejegység beszerelése
  • A fejegység – PUMPKIN Android 9.0 Double Din Review
    • A PUMPKIN-ról
    • Kivétel a dobozból

Telepítés áttekintése:

  • Jármű:2005-ös Mercedes Benz CLK 320
  • Fejegység:Pumpkin Android 9.0 Double Din fejegység
  • Nehézségi fok:Közepes
  • Idő:3-5 óra

Valljuk be, a 2000-es évek legtöbb járművében van fejegység, vagy általában az autóhifi technológia, ami elavult. A Bluetooth éppen befogott (bár az aux bemenetek voltak a lényeg), a GPS-navigáció luxus volt, az érintőképernyős fejegység pedig gyárilag kevés volt. Abban az időben a 05 CLK 320 nagyszerű, stílusos és fényűző autó volt, de ahhoz, hogy a modern korba kerüljön, frissítésre van szüksége.

Árbarát, de nagy teljesítményű fejegységet kerestünk a 2005-ös CLK 320-as sztereó rendszerünk frissítéséhez, és a legújabb technológiával való felgyorsításhoz, hogy megfelelő ingázóvá tegyük. Nagyon izgatottak voltunk, amikor a PUMPKIN megkeresett minket egy olyan egységgel, amelyet tesztelhetünk náluk.

A fejegység – PUMPKIN Android 9.0 Double Din

Ez a telepítés szinte minden dupla din érintőképernyős fejegységre, az Apple CarPlay-re és az Android Auto-ra, illetve a dupla din-es multimédiás fejegységre vonatkozik, függetlenül attól, hogy melyik egységet választottuk a telepítéshez. Ha a telepítés során használt termékhez szeretne illeszkedni, akkor a PUMPKIN Android 9.0 Double Din AA0495B típusú fejegységét választottuk. Megtalálható az Amazonon és közvetlenül a Pumpkin oldalán itt.

A PUMPKIN-ról

A PUMPKIN egy kínai székhelyű gyártó, amelyet 2014-ben alapítottak. Elsősorban az európai piacra koncentrálnak, de az Egyesült Államokban is jelen vannak. Alaptermékeik között megtalálhatók az OEM cserefejegységek, a két- és egy din fejegységek, a hordozható és a kettős fejegységek. képernyős DVD-lejátszók, valamint fejtámla monitorok. A legtöbb termékük Android rendszer, beleértve azt is, amelyet a CLK 320-unkba telepítettünk.

Kivétel a dobozból

A dobozban a PUMPKIN fejegység a következőket tartalmazza:

  • 1x Android fejegység
  • 1x ISO-kábel
  • 1x külső mikrofon
  • 1x USB+ mikrofonkábel
  • 1x hangkimeneti kábel
  • 1x wifi antenna (4,9 láb)
  • 1x GPS antenna
  • 1x AUX bemeneti kábel
  • 1x Cam-in kábel
  • 1x telepítési tartozékok (vezetékköteg)
  • 1x felhasználói kézikönyv

Telepítés 2002-2005 Mercedes CLK320

Vegye figyelembe, hogy az alábbi utasítások és alkatrészek a Harman Kardon NÉLKÜLI CLK320-ra vonatkoznak. Ha fejegységet szeretne beszerelni a Harman Kardon/erősített sztereóval rendelkező CLK320-ba, akkor speciális kábelkötegre lesz szüksége. Mindent az egyben, így csak ezt a hevedert kell lecserélnie az alábbiakban bemutatott Axxess kábelkötegekre.

A telepítéshez szükséges alkatrészek:

  • Fejegység (természetesen) – A PUMPKIN dupla din fejegységünket használtuk
  • Axxess XSVI-9005-Nav kábelköteg – az OEM Mercedes fejegység vezetékeit az utángyártott fejegységhez igazítja. Kiegészítő 12 V-os tápot is létrehoz. E kábelköteg és adapter nélkül más forrást kell találnia a tartozék bekapcsolási tápellátásának bekötéséhez. Ez a kábelköteg közvetlenül az alábbi ASWC-1-hez is csatlakozik.
  • Axxess ASWC-1 – Kormánykerék-vezérlő interfész. Nem kötelező, ha meg szeretné tartani a kormánykerék kezelőszerveit.
  • Metra 40-EU10 – Az OEM rádióantenna csatlakozóját egy utángyártott csatlakozóhoz igazítja.
  • Metra 99-874B – Műszerfal készlet, amely a dupla dint a gyári műszerfal kivágásához igazítja.

Íme egy gyors áttekintés azokról a termékekről, amelyeket a telepítéshez választottunk.

1. lépés:Válassza le az akkumulátort

Először is le kell választania az akkumulátort, hogy ne üsse ki a biztosítékokat a telepítés során. A CLK 320 akkumulátora az autó utasoldalán, a motorháztető alatt található, közvetlenül a tűzfal előtt. Távolítsa el a negatív pólust az akkumulátor bal oldalán (ha felé néz).

2. lépés:Távolítsa el a Dash Trim-et

Kezdje a konzol díszítőelemével, amely körülveszi a sebességváltó csomagtartóját. Nyissa ki a hamutálcát, és húzza felfelé elölről, hátrafelé haladva. Ezután óvatosan húzza felfelé a váltócsomagtartó hátsó részét, és haladjon előre. Miután eltávolította a csomagtartó burkolatot, átvezetheti ezt a díszelemet a konzol burkolatán lévő lyukon, és teljesen eltávolíthatja a konzol díszítőelemét.

Ezután távolítsa el a hamutálcát úgy, hogy az alján lévő két fogazott kapcsot maga felé húzza, és kiemeli a műszerfalból.

Most, hogy a hamutálca kikerült az autóból, két Torx csavarhoz férhet hozzá a klímaberendezés alatt. Távolítsa el ezt a két csavart, és húzza ki a klímaberendezést. Ne feledje, hogy a felső sarkokban két kapocs van, amelyek bent tartják, és „kiugrik”, amikor húzza. Az egység eltávolítása után meg kell húzni a csatlakoztatott vezetékeket – kettőt kell eltávolítani. Távolítsa el ezt a két vezetéket, és távolítsa el az egységet a műszerfalról.

A klímaszabályozás eltávolítása után hozzáférhet a fejegységben lévő két alsó csavarhoz. Mindazonáltal kettő van az egység felett is, így mielőtt eltávolítaná őket, le kell húznia a burkolatot és a fejegység felett található gombokat. Ehhez nyomja meg a pohártartót, hogy a pohártartó kinyúljon. Ujjaival húzza meg a panel jobb belső sarkát a sarok kioldásához, majd haladjon balra. A díszítőelem eltávolítása után pattintsa le a kábelköteget az egység hátuljáról, hogy teljesen eltávolítsa.

4. lépés:Készítse elő a kábelköteget és a fejegységet

Amikor az OEM-fejegység ki van szerelve, és a műszerfal készen áll az új fejegységhez, a következő lépés a kábelköteg-adapter és a fejegység előkészítése az autóba való beszereléshez. In our case, the adapting Axxess XSVI-9005-Nav and ASWC-1 plugged together, but we needed to adapt the aftermarket head unit wire harness to the vehicle adapting Access harnesses. To do this, we soldered each of the wires from one harness to the corresponding wire on the other. Typically, all of the colors will match but just in case, we have a list of all of the aftermarket wire colors to help guide you.

Couple things to note:

  1. Brake wire – we typically just combine this with the main ground wire so that any features that are restricted by movement will be unlocked. Note that some units are smarter and use GPS to sense motion but this will typically open up any video or other features that are locked when your vehicle isn't in park.
  2. Steering wheel control – the ASWC-1 comes with a 3.5mm plug that will adapt to most head units by plugging into the rear of the unit. However, in some cases it needs to be further adapted into two wires:Key 1 and Key 2. These two wires will need to be connected to the corresponding Key 1 and Key 2 wires from the aftermarket head unit harness.

You can either solder each of the wires like we did, or use crimps and a crimping tool. Here's what the resulting wire harness looked like:

To prepare your head unit to be mounted into the dash, you'll need to mount your new aftermarket head unit to the Metra 99-874B dash kit. Do this by mounting the two left and right mounting plates to the head unit losely. Once they're mounted, place the adapting dash trim over the face of the head unit to check your mounting point and that the unit sticks out as far as you would like it. If your satisfied, tighten the side plates and mount the trim piece to the side plates.

Step 5:Wiring Accessories – Antennas, USB &Microphone

Before you mount your new head unit in the dash, you need to make sure that all the wiring that plugs into the back of the head unit are wired into the back of the dash. This includes things like:

  • USB chords
  • GPS and WiFi Antennas
  • Microphone

The PUMPKIN head unit that we chose had all of the above so we wired up all three to the back of the dash before we re-installed our new head unit.

USB Chords

Our head unit came with two usb inputs that are wired up to the back of the head unit, so we had to choose a spot for the new USB chords to go and then wire them. In our CLK 320, we decide to utilize the ash tray below the head unit. No need to cut holes, simply pull the removable ash tray component out of the ash tray cubby and feed the wires into the ash tray cubby.

GPS &WiFi Antennas, Microphone

For all three of these components, we fed the wire from the dash area, underneath the steering wheel and to the far left side of the dash. To do this, there's a panel above your feet that has two torx screws. Remove the torx screws and pull the panel to gain access to behind the dash under your steering wheel. Then, remove the panel on the left hand side of the dash that faces the door (when closed). Feed the wires from the central dash area through to the left side of the dash. We used zip tie to fasten the wire under the dash.

Once your GPS, WiFi and microphone (or any combination of the three) are through the dash and out of the side panel of the dash, we mounted the WiFi antenna straight to the dash right next to the fuse box. Continue to feed your GPS and Microphone up through the pillar by placing the wire in between the pillar panel and the rubber seal. Tuck your wires behind the pillar panel.

At the top of the pillar, feed your wires across and to the window. We typically mount our microphones in the top left hand side of the windshield and clip it in between the head liner and the windshield. For the GPS, continue to tuck the wire behind the head liner through to the left hand side of the rear view mirror. This is where we mounted our GPS unit.

Step 6:Installing Your New Head Unit

Finally, you're ready to re-install your head unit and connect all of the wires. One last step before you place start connecting your head unit and screwing it in – use the Metra 40-EU10 to connect to the black antenna wire that was connected to the back of your OEM head unit (there was a black and a yellow/tan one – use the black). Plug the antenna wire into the back of the unit.

Now, move on to the microphone, GPS and WiFi connections (if your head unit has them). Connect these to the back of the unit. Finally, connect your new adapting harness with the Axxess modules connected and tuck the modules behind where the climate control would go. You'll need to make as much room behind the head unit so that it will have enough depth to mount. If you don't tuck your wires and modules neatly out of the way of the back of the head unit it will not have enough room to mount flush.

At this point, you should have all of your wires connected and the head unit should not be fully mounted yet. Re-connect your vehicle's battery and test out your unit. You'll want to check:

  1. Power – obviously this is the most important first-check
  2. Radio – check sound and that the radio has reception
  3. GPS – If your unit has GPS ensure that it has signal
  4. Bluetooth call – make sure that your new microphone works
  5. USB – check that your USB connection works
  6. WiFi – in our case we had a WiFi antenna, check that you have signal and that you can connect to a WiFi network
  7. Test general features – Roam around the features of your new head unit. Make sure that nothing is defective before you permanently re-install it!

Once you've checked your unit and everything is confirmed working, you can begin mounting it back. Mount the unit by screwing the four torx screws.*Note – the climate control has clips that you'll need to remove from the old head unit. Take these clips and place them on the back side of the screw holes on your new unit BEFORE you screw it in.

Move on to the trim pieces, reversing the process that you took to remove them. And your finished product:


  1. Hogyan telepítsük az Ellipse műholdas antenna
  2. Dupla DIN Stereo specifikáció
  3. Hogyan telepítsük a videó Feladó
  4. Hogyan telepítése egy Amp A CQ- C8100u Head Unit ?
  5. Hogyan telepítsük a Boss erősítő a fejegység