1. kamerák
  2. Car Audio & Electronics
  3. Home Audio
  4. Personal Audio
  5. TV-k
  6. Okos otthon
  >> Elektronikai Technológia Online >  >> Car Audio & Electronics >> autó rádiók

Hogyan lehet a semmiből bekötni egy autós sztereót?

Utazott már valaha egy kiváló autóban, de rossz minőségű zenéje volt? Sajnos ez a legtöbb autóban probléma volt.

Általában sok autó gyárilag felszerelt fejegységekkel érkezik, amelyek nem felelnek meg a követelményeknek. Ennek az az oka, hogy a legtöbb autógyártó nem fekteti a legnagyobb erőfeszítést az autók hang- és audioberendezéseinek minőségére.

A leggyakoribb és legjobb döntés ilyenkor az autós fejegységet egy utángyártott rádióra cserélni, de hogyan kell az autóhifit a semmiből bekábelezni? Nézzük meg.

Az autórádió bekötésének első lépése a kábelköteg eltávolítása, valamint a hangszórókat és a tápellátást összekötő vezetékek leválasztása. Ezután rögzítse a vezetékeket az új kábelköteghez vagy a kábelköteg-adapterhez, és csatlakoztassa az új rádióhoz. Ha csatlakoztatta, tesztelje az autórádiót, és ha megfelelően működik, helyezze be a műszerfalba.

A teljes csere folyamat magában foglalja az autórádió beszerelését és bekötését. Ebben a cikkben lépésről lépésre bemutatom az autórádió bekötését.

Az autórádió vezetékezése a semmiből. Átfogó útmutató.

Más folyamatokhoz hasonlóan a sztereó bekötésére vonatkozó megfelelő utasítások követése biztosítja, hogy autójában kiváló minőségű hang legyen.

Szánjon időt arra, hogy minden lépést figyelmesen elolvasson, és ennek megfelelően cselekedjen. Ügyeljen arra, hogy ne dolgozzon sietve, és fordítson nagy figyelmet a munkára.

Milyen eszközökre van szükség az autós sztereó bekötéséhez?

Mielőtt bármit is tenne az autórádióval, néhány alapvető, de szükséges eszközt elő kell készítenie.

Valószínűleg minden a garázsában van, de ha nem, hozzáadtam az Amazon-linkeket az általam használt eszközökhöz, és elégedett vagyok a minőséggel:

  • Digitális multiméter.
  • Dróteltávolítók.
  • Crimperek.
  • 9 voltos akkumulátor- vagy hangszórótesztelő.
  • Elektromos szalag.

1. lépés:Távolítsa el a rádiót, és válassza le a kábelköteget

Először távolítsa el a régi sztereót a műszerfalból, és válassza le a kábelköteget. Ezen a ponton, az új rádiótól függően, szükség lehet egy vezeték-adapterre hogy segítsen az új autórádió csatlakoztatásában az autó meglévő csíptetőjéhez.

A kábeladapter segít az egyedi autóhifi készülékek szabványos DIN-csatlakozóval történő csatlakoztatásában az autóból, és elkerüli a hibás csatlakozásokat.

2. lépés:Az akkumulátor leválasztása

A bekötési folyamat során az elektromos rendszeren kell dolgoznia.

Emiatt fennáll az áramütés veszélye, ezért ajánlatos az akkumulátort lecsatlakoztatni a vezetékcsatlakoztatás megkezdése előtt.

A legtöbb autóban az akkumulátor a motorháztető alatt található, néhány ritka esetben, ha a jármű hátuljába szerelik be.

Az akkumulátor megtalálása után egy kézi vagy dugaszolókulcs segítségével lazítsa meg a fekete kábelt az akkumulátor negatív pólusáról.

Fontolja meg a csavar elvesztését, és húzza le a kábelt az akkumulátor oldalára, hogy megbizonyosodjon arról, hogy nem ér hozzá a pozitív vezetékekhez. Az akkumulátor leválasztásának elmulasztása károsíthatja Önt vagy az autó elektromos berendezését.

3. lépés:Tekerje be az összes csatlakoztatott vezetéket

Ennek az a jelentősége, hogy biztosítsák a csatlakozási pontjaikat.

Az összes vezeték ellenőrzése és az autóhoz való csatlakoztatása után elengedhetetlen a csatlakozások állandósítása.

Győződjön meg arról, hogy nincs csupasz vezeték az autórádióban, és a vezetékcsatlakozások megvetemítéséhez használhat elektromos szalagot. .

Használhat más módszereket is a vezetékek tekercselésére, de a szalag használata a legegyszerűbb, legolcsóbb és a legtöbben használt módszer.

3. lépés:Tesztelje autórádióját

A csatlakozások elkészítése és rögzítése után újra kell csatlakoztatnia az akkumulátort, hogy tesztelje a sztereót, mielőtt véglegesen a műszerfalra helyezi.

It is advisable to install the car radio after checking it is working perfectly. First, however, you need to check its all functions, including speakers connections.

Finding something that is working incorrectly means the wires are not connected right, and often mistake is wrong connection of the speaker wires.

Step 4:Place the Wires Harness Into the Dashboard

After ensuring that all of your connections are tight and secure, it’s now time to install wiring inside the dash.

This includes connecting an often-forgotten antenna wire from car radio signal reception equipment so you can enjoy clear communications while driving!

You have to remember that there should be enough space for your radio in the dashboard, so make sure all wires are pushed into the dashboard.

This way, the stereo won’t get stuck when trying to move or remove from its position later on without damaging anything!

Step 5:Place the Car Radio Into Its Place

In most cars, there is an opening inside the dash where the car radio should be placed.

While installing the car radio, make sure it perfectly fits into the slot, and there are no extra wires that would block free movement.

If you feel some resistance while pushing the radio, never force it with too much pressure to its position. Otherwise, you can damage the wiring connectors at the backside.

In this case, an adaptor is very helpful at sliding the car radio properly in its correct position. An adaptor is available at any electronic store or auto parts store.

Step 6:Secure the Car Radio in Its Position

You can secure a car radio into two main methods.

  • One of them is for the car radios that need spring clips. Once the stereo is locked at the correct position, the clips close and you can hear a click sound.
  • The other one that is less common, involves brackets and bolts that need proper fixation. Bolting the radio permanently helps to secure it in the place.

Step 7:Install Dashboard

This is the final step of the wiring process and involves assembling every piece of the trim and the plastic clips.

At the same time, be careful to avoid the damage of any plastic parts and take time to check if the overlapped pieces have been correctly layered.

If you come across some plastic parts that have been broken, you can use hot glue to secure them.

However, using glue is not highly recommended since the plastic parts you fix can become difficult to remove in the future.

If the entire rim piece has been broken completely, the only option you have is to buy a replacement.

How to Test Car Radio Wire for Their Right Connections

All wires have to be in good condition and connected to the radio without interruptions.

Below I listed a few simple checks you can do to make sure the stereo’s connection is correct:

Constant wire

This wire comes with 12 volts, and it supplies power directly from the battery.

To test if it is working, the first thing you should do is put off your ignition. Afterward, ground the black wire, pick up the red meter probe and connector, and touch it with the constant yellow wire.

The constant wire should give the reading up to 12 volts with a 0.5V difference.

Speaker wire

The simplest way to test the speaker wires is to use a 9-volt battery. You can also use a multimeter to test the speakers but make sure you set it to resistance before testing.

Accessory Power

Turning off the ignition makes the wire show a zero volt reading at a meter. Upon turning it on, it reads 12 volts and 0.5 volts.

Ground wire

Identifying the ground wire is straightforward after identifying the constant wire. Then, after proper testing, the ground wire is connected to the black wire.

Note that it is necessary to begin attaching a red meter probe with constant wire and later a black meter probe with the wire you are testing.

If the reading on the meter is similar to the constant wire testing, that is the ground wire.

Gyakran Ismételt Kérdések (GYIK)

Where Is the Ignition Wire Located?

Depending on the car, the ignition switch harness is located inside the steering wheel column on either the left or right side.

The ACC wire is the one often 18 gauge yellow or pink. Installing this wire at a local electrical specialist can help you ensure the installation.

What Happens if You Do Not Ground a Car Stereo?

It is impossible to operate a car stereo without a proper ground wire installed.

The correct ground connection allows your radio to work perfectly without malfunctioning issues when the car is on.

How Can I Tap the Wires When Wiring a Car Stereo Without the Harness Clip?

The best solution is to look at your car’s electrical manual. However, if the manual is unavailable, you have to trace every wire.

Using a multimeter will be a good idea in this task. Since car electrical systems can be tricky to manage, do not attempt to play with the car’s electrical system without basic knowledge.

Következtetés

You have no reason to stay in an excellent car with a poor music system with the above guides.

Remember, adding a new car radio in your car is a great way to breathe new life into your vehicle. However, for the stereo to work at its own best, you have to follow the installation and wiring process.


  1. Hogyan kell bekötni az XM Radio
  2. Hogyan Wire Sony CXD3141
  3. Hogyan kell bekötni az IR Remote Autórádió
  4. Hogyan Wire Sony CDX- F5500
  5. Hogyan Wire Craig Autórádió